Esquema Harman Driver de titânio, Manuais, Projetos, Pesquisas de Eletrônica

Baixe Esquema Harman Driver de titânio e outras Manuais, Projetos, Pesquisas em PDF para Eletrônica, somente na Docsity!

harman/kardon

HKTS 10

Home Cinema Speaker System

SERVICE MANUAL

harman/kardon, Inc.

250 Crossways Park Dr.

Woodbury, New York 11797 Rev0 8/

CONTENTS

SPECIFICATIONS......................... ...... .......... .. ... ...... .. ......... 1

DETAILED SPECIFICATIONS..................... …………...... ...... ............ 2

CONTROLS & CONNECTIONS............. ............... ........... ........... 3

OPERATION & ADJUSTMENTS............. ................ .......... ........... 8

BASIC TROUBLESHOOTING GUIDE.................. ............... ............. 9

SUB-TS10 TEST PROCEDURE............. ................ .......... ........... 10

SUB-TS10 BLOCK DIAGRAM.................... ................. ... .. ......... 11

MECHANICAL/PACKING PARTS LIST ……..... ......... .. ..... .. .......... ... ........ 12

SUB-TS10 EXPLODED VIEW.................... ......... ..... ..... ... .. ....... …. 13

SUB-TS10 PCB DRAWINGS. ................ …... ........ …........ ... .. ......... 14

SUB-TS10 IC – TRANSISTOR PINOUTS. …... ......... ……..…........ ... .. ......... 16

SUB-TS10 ELECTRICAL PARTS LIST …………. ............ .... ............ ... ........ 17

SUB-TS10 SCHEMATIC DIAGRAMS.................... ... .. .. ..... ... ..............

SPECIFICATIONS

HKTS 10 System Frequency Response 35Hz – 20kHz (–6dB)

SAT-TS10 Satellites

Recommended Power

10 – 110 watts

Impedance

8 ohms nominal

Sensitivity

86dB @ 1 watt/1 meter

Tweeter

One 1" dome, video-

shielded

Midrange

One 4" driver, video-

shielded

Dimensions (H x W x D)

10-1/8" x 5-1/4" x 5-3/8"

257mm x 133mm x 137mm

Weight

6.6 lb/3.0kg

CEN-TS10 Center

Recommended Power

10 – 110 watts

Impedance

8 ohms nominal

Sensitivity

86dB @ 1 watt/1 meter

Tweeter

One 1" dome, video-shielded

Midrange

Dual 4" drivers, video-

shielded

Dimensions (H x W x D)

5-1/16" x 16-1/2" x 5-3/16"

128mm x 418mm x 131mm

Weight

10 lb/4.5kg

SUB-TS10 Subwoofer

Amplifier

150 watts RMS

Bass Driver

12" woofer, bass-reflex

enclosure

Dimensions (H x W x D)

20-5/16" x 16-3/8" x 15-1/16"

515mm x 416mm x 382mm

Weight

40 lb/18.0kg

Occasional refinements may be made to existing products without notice but will always meet or exceed original

specifications unless otherwise stated.

SUB-TS10 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS

¡ Speaker-Level Inputs: Connect these binding post terminals to the main left and right speaker terminals of your receiver or amplifier, if your receiver or amplifier does not have a line-level subwoofer output. Remember to maintain polarity by connecting the (+) terminal on the receiver/amplifier to the (+) terminal on the SUB-TS10 subwoofer, and the (–) terminal on the receiver/amplifier to the (–) terminal on the SUB-TS10 subwoofer. ™ Speaker-Level Outputs: If you are using the Speaker-Level Inputs ¡ on the SUB-TS10, you should connect these binding post terminals to your front left and right speakers, remembering to maintain polarity by connecting the (+) terminal on

the SUB-TS10 subwoofer to the (+) termi- nal on the speaker, and the (–) terminal on the SUB-TS10 subwoofer to the (–) terminal on the speaker. If you are not using the Speaker-Level Inputs ¡, then connect your front left and right speakers directly to your receiver or amplifier. See pages 6 and 7 for further information. £ Line-Level Subwoofer (SUB) Input: Connect the subwoofer output of a receiver with digital surround sound decoding, such as Dolby* Digital or DTS® , to this input. This input bypasses the SUB-TS10’s internal crossover circuitry, and should only be used with a filtered signal. If your receiver does not have digital decoding, you should use the

Line-Level Full-Range Inputs ¢ instead. ¢ Line-Level Full-Range Inputs: Con- nect the line-level subwoofer output or preamp output(s) of your receiver or amplifier to these inputs. If your receiver does not have a separate subwoofer output, use a Y-adaptor (not supplied) to bridge the receiver’s preamp output to the main amp input for that chan- nel, and connect the long end of the adaptor to the corresponding line-level input on the SUB-TS10. If your receiver has only a single subwoofer output, you may connect it to either the left or right line-level input on the SUB-TS10, and no Y-adaptor is needed. ∞ Phase Switch: This switch determines whether the SUB-TS10 subwoofer’s piston-

RISK OF ELECTRIC SHOCK RISK OF ELECTRIC SHOCK RISK OF ELECTRIC SHOCK^ CAUTION^ CAUTION DO NOT OPENDO NOT OPENDO NOT OPEN

harman/kardon

SUB-TS10 For use withHKTS 10 System

OFF

NORMAL REVERSE

OOFER LEVEL

ON AUTO IMPORTANT: CONNECT STRIPED WIRE TO RED ( ) SPEAKER TERMINAL.

AC 120V~60Hz

Made in China POWER

L R

SUB

PHASE

FILTER CONTROL SUBW GREEN: ONRED: STAND-BY

REMOTEFILTER

LEVELLINE IN ON

R L

¡ Speaker-Level Inputs ™ Speaker-Level Outputs £ Line-Level Subwoofer (SUB) Input ¢ Line-Level Full-Range Inputs ∞ Phase Switch § High-Cut (Low-Pass) Filter Switch ¶ Music-Sense On/Off Switch

• Filter Remote Control Input ª LED Indicator ‚ Subwoofer-Level Control ⁄ Master Power Switch ¤ AC Power Cord

SUB-TS10 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS

like action moves in and out in phase with the main speakers. If the speakers were to play out of phase, the sound waves pro- duced by the subwoofer would be cancelled out, reducing bass response. This phenome- non depends in part on the relative place- ment of the speakers in the room. In most cases, the Phase Switch ∞ should be left in the NORMAL position. However, it does no harm to experiment with the Phase Switch ∞, and you may leave it in the position that maximizes bass response. § High-Cut (Low-Pass) Filter Switch: Placing this switch in the ON position acti- vates circuitry that cuts out all audio input signals above 120Hz. This allows the SUB- TS10 to focus its power on reproducing the low-frequency portion of the signal, avoid- ing inefficiency and distortion. Engage this filter when using the Speaker-Level Inputs ¡, or when using the Line-Level Full-Range Inputs ¢, unless your receiver or processor processes its line-level output using a low-pass filter. The filter has no effect when the SUB Input £ is used. ¶ Music-Sense On/Off Switch: When placed in the AUTO position, and when the Master Power Switch ⁄ is turned on, the SUB-TS10 will automatically turn itself on or place itself in the Standby mode, depending on whether it is receiving an audio signal. When this switch is placed in the ON posi- tion, the SUB-TS10 will remain on, whether or not it is receiving an audio signal.

• Filter Remote Control Input: This input accepts a remote control signal from a compatible Harman Kardon A/V receiver that enables you to override the High-Cut

(Low-Pass) Filter Switch §, by signal- ing the SUB-TS10 to engage the filter even when the switch is in the OFF position. ª LED Indicator: This LED indicates whether the SUB-TS10 is in the ON or STANDBY state when used with the Music-Sense On/Off Switch ¶ in the AUTO position. The LED is lit Green to indicate that the SUB-TS10 is receiving an audio signal and is turned on, and the LED is lit Red to indicate that no signal is being received and the SUB-TS10 is in Standby mode. When the Music-Sense On/Off Switch ¶ is in the ON position, the LED will be lit Green, whether or not an audio signal is present. When the Master Power Switch ⁄ is turned off, the LED goes dark, no matter which position the Music-Sense On/Off Switch ¶ is in. ‚ Subwoofer-Level Control: Volume can be adjusted using the Subwoofer- Level Control. Turn the control clockwise to increase the SUB-TS10’s volume, or counterclockwise to decrease it. ⁄ Master Power Switch: Place this switch in the “•” position to power-on the SUB-TS10 subwoofer. The SUB-TS10 will then be either in the Standby mode or completely on, depending on the position of the Music-Sense On/Off Switch ¶. ¤ AC Power Cord: Make sure to plug this cord into an active, unswitched electri- cal outlet for proper operation of the SUB- TS10. The cord should not be plugged into the accessory outlets found on some audio components.

SPEAKER CONNECTIONS (continued)

Receiver

SUB/LFE

Out

Front Left

Surround Left

Front Right

Surround Right

SUB-TS

Subwoofer

Center

Line-Level

L

R

Surround

Right

Front

Right

Surround

Left

Front

Left

Center

- + - + **- +

• +**^ –^ +

Dolby Pro Logic

(Non-Digital) – Line Level

USE THIS INSTALLATION METHOD FOR

DOLBY PRO LOGIC APPLICATIONS (NOT

DOLBY DIGITAL, DTS OR OTHER DIGITAL

PROCESSING), WHERE THE RECEIVER/

PROCESSOR IS EQUIPPED WITH A SUB-

WOOFER OUTPUT, OR A VOLUME-

CONTROLLED PREAMP (LINE-) LEVEL

OUTPUT:

Use the supplied RCA-type patch cord to connect the line-level subwoofer output on your receiver or amplifier to either the left or right Line-Level Full-Range Input ¢ on the SUB-TS10 subwoofer. Use both the left and right inputs on the subwoofer if your receiver or processor has both left and right line-level outputs. If your receiver is equipped with line-level outputs but does not have a separate sub- woofer output, use a Y-adaptor (not supplied) to bridge the receiver’s preamp output to the main amp input for that channel, and connect the long end of the adaptor to the corre- sponding line-level input on the SUB-TS10. IMPORTANT: Do not use the SUB Input £ on the subwoofer with Dolby Pro Logic processors. Make sure that you have config- ured your surround sound processor for “Subwoofer On.” The front left, front right, center and rear surround speakers should all be set to “Small.” When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier.

Front Left Front Right

Surround Left Surround Right

Center

Front Left

Surround Left

Center Front Right

Surround Right

Receiver

- + – + **- +

• • – +**

SUB-TS

Subwoofer

R L

SPEAKER CONNECTIONS (continued)

Dolby Pro Logic*

(Non-Digital) – Speaker Level

USE THIS INSTALLATION METHOD FOR

DOLBY PRO LOGIC APPLICATIONS (NOT

DOLBY DIGITAL, DTS OR OTHER DIGITAL

PROCESSING), WHERE THE RECEIVER/

PROCESSOR DOES NOT HAVE A SUB-

WOOFER OUTPUT, OR A VOLUME-

CONTROLLED PREAMP (LINE-) LEVEL

OUTPUT:

Connect your receiver or amplifier’s front left and right speaker terminals to the left and right Speaker-Level Input ¡ terminals on the SUB-TS10 subwoofer that are marked “High Level In.” Connect the left and right Speaker-Level Output ™ terminals on the SUB-TS10 subwoofer that are marked “High Level Out” to the corresponding terminals on the back of your front left and right speakers. Connect your receiver or amplifier’s center, and surround left and right speaker terminals to the corresponding terminals on the back of your center, and surround left and right speakers. When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet.

If there is no sound from any of the speakers:

• Check that receiver/amplifier is on and a source is playing.
• Check that the powered subwoofer is plugged in and its Master Power Switch

⁄ is switched on to the “•” position.

• Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.
• Review proper operation of your receiver/amplifier.

If there is no sound coming from one speaker:

• Check the “Balance” control on your receiver/amplifier.
• Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, and that no wires are touching each other.
• In Dolby Digital or DTS mode, make sure that the receiver/processor is configured so that the speaker in question is enabled.
• Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem is in the same place: i.e., the speaker that was working previously now has no sound and the speaker that was not working now sounds fine; or whether it has moved: i.e., the speaker that was not work- ing still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner’s manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at www.harmankardon.com for further information.

If there is no sound from the center speaker:

• Check all wires and connections between receiver/amplifier and speaker. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.
• If your receiver/processor is set in Dolby Pro Logic mode, make sure the center speaker is not in phantom mode.
• If your receiver/processor is set in Dolby Digital or DTS mode, make sure the receiver/processor is configured so that the center speaker is enabled.

If the system plays at low volumes but shuts off as volume is increased:

• Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.
• If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier.

If there is low (or no) bass output:

• Make sure the SUB or line-level inputs of the SUB-TS10 subwoofer and SUB or LFE output of your receiver or amplifier are properly connected by the RCA-type patch cord.
• If you are using the SUB-TS10’s speaker- level inputs, check your speaker cables to make sure they are all connected; that none of the wires are frayed, cut or punctured; and that you have maintained the correct polarity by connecting positive terminals to positive terminals, and negative terminals to negative terminals.
• Make sure the subwoofer is plugged into an active electrical outlet and its Master Power Switch ⁄ is switched on to the “•” position.
• Check the speaker setup (bass manage- ment) settings in your AVR receiver or processor to make certain that the front, center and surround speakers are config- ured for “Small,” and that the subwoofer is set for “Yes” or “On.”

If there is no sound from the sur- round speakers:

• Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.
• Review proper operation of your receiver/processor and its surround sound features.
• Make sure the movie or TV show you are watching is recorded in a surround sound mode. If it is not, check to see whether your receiver/processor has other surround modes you may use.
• In Dolby Digital or DTS mode, make sure your receiver/processor is configured so that the surround speakers are enabled.
• Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby Digital or DTS mode, and that you have properly selected that mode using both the DVD player’s menu and the DVD disc’s menu.

TROUBLESHOOTINGTROUBLESHOOTING

RISK OF ELECTRIC SHOCK RISK OF ELECTRIC SHOCK RISK OF ELECTRIC SHOCKDO NOT OPEN^ CAUTION DO NOT OPEN^ CAUTION DO NOT OPEN

harman/kardon

SUB-TS10 For use withHKTS 10 System

OFF

NORMAL REVERSE

OOFER LEVEL ON AUTO IMPORTANT: CONNECT STRIPED WIRE TO RED ( ) SPEAKER TERMINAL.

AC 120V~60Hz

Made in China POWER

L R

SUB PHASE

FILTERCONTROL GREEN: ON SUBW RED: STAND-BY

R L LEVELLINEIN ON REMOTEFILTER

{

AC VOLT GENERATORSIGNAL METER (10V)

AMPLIFIER

Equipment needed:

• Function/signal generator/sweep generator
• Integrated Amplifier
• Multimeter
• Speaker cables

General Unit Function (UUT = Unit Under Test)

1) From the signal generator, connect one line level (RCA) cable to the single Sub input on the UUT.

2) On the front of the unit, turn the LEVEL control full counterclockwise. FILTER control should be OFF.

3) Turn on generator, adjust to 75mV, 50 Hz.

4) Plug in UUT; turn the power switch ON. LED should be Red. Turn LEVEL control full clockwise (MAX)

5) LED should now be Green; immediate bass response should be heard and felt from port tube opening.

6) Turn off generator, turn VOLUME control fully counterclockwise, disconnect RCA cable.

7) Connect one pair of speaker cables to Speaker Level input terminal (IN) on Right channel only. Cables

should be connected to an integrated amplifier fed by the signal generator.

8) Turn on generator and adjust so that speaker level input at the amplifier is 1.6V, 50 Hz. Turn LEVEL control

full clockwise.

9) Green LED should light, immediate bass response should be heard and felt from the port tube opening.

Sweep Function

1) Follow steps 7-9 above, using a sweep generator as a signal source.

2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any

other noises. If any unusual noises are heard, remove woofers and test.

Driver Function

1) Remove woofer from cabinet; detach + and - wire clips.

2) Check DC resistance of woofer; it should be 3.5 ohms ±10%

3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed

by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.

4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.

Test Set Up and Procedure

HKTS 10

HKTS

UNDER TEST

Part Number Description

Subwoofer SUB TS

30PF14FM-DW02 12" Woofer (DCR = 3.5 ohms +/-10%)

xc125006-b Front Baffle

xc125007 Grille

wi5334-1 Foot (4)

06-T5305004 Screw for front baffle & Feet (8)

Satellites SAT-TS

10PR70BZK-HW02 4" woofer

35DM13NG-PT02 13 mm tweeter

XR5176-1 Crossover Network

xc045016-b Baffle

xc045017-1 Grille

xd045016-b Enclosure

Center Channel CEN-TS

10PR70BZK-MW02 Woofer 4"

35DM13NG-HT02 13mm tweeter

xr5177-1 Crossover Network

xc045014-b Baffle

xd045014-b Enclosure

xc045015-1 Grille

Packing/Accessories

wg5320 Master carton

ai5170 Owner's manual

at5108 Warranty card

sal5009 Wire set 40' (surround)

sal063-1 Wire set 20' (center)

sal5020 Wire set 15' (front satellites)

sal5044 15' RCA cable

wi5688 Center Channel Bracket/Support

wi5689 Foot

wi5691 Wall Bracket for Satellite

HKTS 10 Subwoofer/Satellite/Center Mechanical/Packing Parts List

HKTS 10

harman/kardon

16

Integrated Circuit Diagrams

C

B

E

TIP31C NPN,

TIP32C PNP,

Q501, 502

4558 DUAL OP AMP,

U

OPAMP, QUAD 14P DIL TL

U201, 202, 301

TRANS, PNP, 2N5401 TAP,

TO-92,

Q

TRANS, PNP, TAP,

2SA1015GR

Q101,107,

TRANS, NPN, 2N5551 TAP,

Q114,

TRANS, NPN, 2SC1815GR TAP,

2SC2235 Q108,109,111,113,

Q201-204,206-208,301,

00340-

Part # Description QTY Reference Designator

1353106m50 Electrolytic Cap. 10U 50V ±20% 12 C201,202,206,213,219,231,241,243,251,253,319,

17420810360g SPK JK.BP 8PIN SH0810360G 1 JK202 (Set of eight)

Power Amp Module PW150D

Part# Ref. Designator Description Qty

• 11014103j26 Resistor 10K 1/4W ±5% CF 3 R503,504, Resistors
• 11014222j26 Resistor 2.2K 1/4W ±5% CF 1 R
• 11014432j26 Resistor 4.3K 1/4W ±5% CF 1 R
• 11014472j26 Resistor 4.7K 1/4W ±5% CF 1 R
• 11016102j26 Resistor 1K 1/6W ±5% CF 5 R153,213,214,215,
  • 273~277,279,305,306,308,311,314, 222,225~229,230,232,234,235,240,248,260,
• 11016104j26 Resistor 100K 1/6W ±5% CF 6 R122,126,231,263,266,
• 11016105j26 Resistor 1M 1/6W ±5% CF 1 R
• 11016122j26 Resistor 1.2K 1/6W ±5%CF 1 R
• 11016124j26 Resistor 120K 1/6W ±5% CF 1 R
• 11016151j26 Resistor 150 ohms 1/6W ±5% CF 1 R
• 11016153j26 Resistor 15K 1/6W ±5% CF 1 R
• 11016154j26 Resistor 150K 1/6W ±5% CF 1 R
• 11016182j26 Resistor 1.8K 1/6W ±5% CF 2 R145,
• 11016183j26 Resistor 18K 1/6W ±5% CF 1 R
• 11016203j26 Resistor 20K 1/6W ±5% CF 1 R
• 11016205j26 Resistor 2.0M 1/6W ±5% CF 1 R
• 11016221j26 Resistor 220 ohms 1/6W ±5% CF 1 R
• 11016222j26 Resistor 2.2K 1/6W ±5% CF 1 R
• 11016223j26 Resistor 22K 1/6W ±5% CF 5 R238,247,255,256,
• 11016224j26 Resistor 220K 1/6W ±5% CF 2 R272,
• 11016273j26 Resistor 27K 1/6W ±5% CF 2 R223,
• 11016333j26 Resistor 33K 1/6W ±5% CF 1 R
• 11016393j26 Resistor 39K 1/6W ±5% CF 1 R
• 11016472j26 Resistor 4.7K 1/6W ±5% CF 3 R200,207,
• 11016473j26 Resistor 47K 1/6W ±5% CF 7 R106,129,219,249,250,251,
• 11016474j26 Resistor 470K 1/6W ±5% CF 2 R127,
• 11016512j26 Resistor 5.1K 1/6W ±5% CF 2 R210,
• 11016513j26 Resistor 51K 1/6W ±5% CF 1 R
• 11016562j26 Resistor 5.6K 1/6W ±5% CF 1 R
• 11016621j26 Resistor 620 ohms 1/6W ±5% CF 1 R
• 11016751j26 Resistor 750 ohms 1/6W ±5% CF 1 R
• 11016755j26 Resistor 7.5M 1/6W ±5% CF 1 R
• 11016822j26 Resistor 8.2K 1/6W ±5% CF 1 R
• 11016913j26 Resistor 91K 1/6W ±5% CF 4 R203-
• 116161002f26 Resistor 10K 1/6W ±1% MF 2 R301,
• 116161102f26 Resistor 11.0K 1/6W ±1% MF 1 R
• 116162200f26 Resistor 220 ohms 1/6W ±1% MF 1 R
• 116162202f26 Resistor 22.0K 1/6W ±1% MF 1 R
• 11012472j00 Resistor 4.7K 1/2W ±5% 2 R201,
• 11020332jk3 Resistor 3.3K 2W ±5% 1 R
• 11120102jk3 Metal Film Resistor 1K 2W ±5% 1 R
• 11130471jk2 Metal Film Resistor 470 ohms 3W ±5% 2 R501,
• 11350s68j00 Cement Resistor 0.068 ohms 5W 1 R
• 129a154j633 Metallize Cap. 0.15U 63V ±5% MSC 2 C221, Capacitors
• 1302b101k503 Metallize Cap. 100P 50V ±10% 3 C302,303,
• 1302b470k503 Disc Capacitor 47P 50V ±10% 1 C
  • 256,320, 1302f104z503 Disc Capacitor 0.1U 50V +80/-20% 14 C107,117,122,144,232,242,244,245,246,252,254,
• 132103j503 Mylar Capacitor 0.01U 50V ±5% 2 C305,
• 132103ja03 Mylar Capacitor 0.01U 100V ±5% 2 C103,
• 132104ja03 Mylar Capacitor 0.1UF 100V ±5% 4 C123,218,503,
• 132183j503 Mylar Capacitor 0.018U 50V ±5% 2 C223,
• 132223ja03 Mylar Capacitor 0.022uF 100V ±5% 1 C
• 132273ja03 Mylar Capacitor 0.027U 100V ±5% 1 C
• 132473ja03 Mylar Capacitor 0.047uF 100V ±5% 2 C216,
• 1353105m50 Electrolytic Cap. 1U 50V ±20% 1 C
• 1353107m10 Electrolytic Cap. 100U 10V ±20% 2 C114,
• 1353107m16 Electrolytic Cap. 100uF 16V ±20% 1 C
• 1353107m35 Electrolytic Cap. 100U 35V ±20% 2 C507,
• 1353225m50 Electrolytic Cap. 2.2U 50V ±20% 1 C
• 1353216 Electrolytic Cap. 22U 16V ±20% 1 C
• 1353250 Electrolytic Cap. 22U 50V ±20% 3 C225,505,
• 1353227m16 Electrolytic Cap. 220U 16V ±20% 2 C118,
• 1353476m16 Electrolytic Cap. 47U 16V ±20% 1 C
• 132103kb00 Mylar Cap. 0.01U 200V ±10% 1 C
• 1385478m63 Electrolytic Cap.4700U 63V ±20% 1 C
• 1385478m63 Electrolytic Cap.4700U 63V ±20% 1 C
• 192027c1815gr Transistor 2SC1815GR 12 Q108,109,113,201-204,206,207,208,301, Semiconductors
• 192027c2235y Transistor 2SC2235Y 1 Q
• 192028a1015gr Transistor 2SA1015GR 3 Q101,107,
• 1921672n5551 Transistor 2N5551 2 Q114,
• 1921682n5401 Transistor 2N5401 1 Q
  • 216,310, 197131n4148 1N4148 18 D102,103,104,105,143,201,202~208,214,215,
• 19915000335 Zener Diode 3.3V 1/2W 52mm 1 D
• 19915000625 Zener Diode 6.2V 1/2W 52mm 1 D
• 19915001605 Zener Diode 16V 1/2W 52mm 1 D
• 192161tip31c Transistor TIP31C SGS 1 Q
• 192162tip32c Transistor TIP32C SGS 1 Q
• 19510204hgw LED 204HGW Indicator 1 D
• 19700kbu606g Diode 6A 800V KBU606G 1 D
• 197101n4004 1N4004 2 D110,
• 19006m4558d I.C. OPA 4558D Dual Op-amp 1 U
• 19016tl074cn I.C. TL074CN ST Quad Op-amp 3 U201,202,
• 1091ttc802j0 Thermister TTC-802(JS) NTC 1 TH Miscellaneous
• 1201000003 Inductor 10W 2 FB1,
• 171urwh124d Relay RWH-SH-124D (1600 ohm) 1 RL
• 1741jy35421 PHONE JACK 3.5mm JY-3542-01-030 1 JK 1740rca326p JACK RCA-326 PURPLE/WHT/RED 1 JK201 (Set of three)
• 150r4055900a Power Transformer I/P:120V/60Hz 1 T 180tms7210v SWITCH SLIDE 6PIN MS7210V 3 Filter/Phase/Auto-on-off
• 152u602015 Line Cord SVT FT-2 6FT
• 154k31505t0 Fuse 3.15A 250V 30mm UL/CSA 1 F
• 15563032i Fuse Holder HTB-32I 30mm UL/CSA 1 F
• 11812061001j R2,11,29,30 RES, 1.00K 1206 5% Resistors
• 11812061002j R7,9,25 RES, 10.0K 1206 5%
• 118120610r0j R22,23 RES, 10.0 ohms 1206 5%
• 11812061201j R31-46 RES, 1.20K 1206 5%
• 11812062002j R26 RES, 20.0K 1206 5%
• 11812062201j R6,13,16 RES, 2.20K 1206 5%
• 11812062701j R10 RES, 2.70K 1206 5%
• 11812063000j R24 RES, 300.0 ohms 1206 5%
• 11812063301j R14,15,27,28 RES, 3.30K 1206 5%
• 11812063902j R3 RES, 39.0K 1206 5%
• 11812064700j R8 RES, 470 ohms 1206 5%
• 11812064701j R1,5,12 RES, 4.70K 1206 5%
• 11812064702j R17 RES, 47.0K 1206 5%
• 11812064704j R4 RES, 4.70M 1206 5%
• 118120647r0j R20,21 RES, 47.0 ohms 1206 5%
• 141c0101k50 C4 CAP,CA 100pF 50V 10% 1206 NP0 Capacitors
• 141c0220k50 C5 CAP,CA 22pF 50V 10% 1206 SMT NPO
• 141c0561k50 C6 CAP,CA 560pF 50V 10% 1206 NPO
• 141c6104m50 C2,3,7,8,9,10,11,15 CAP,CA 0.1uF 50V 20% 1206 Z5U
• 141c7223k50 C13 CAP,CA 0.022uF 50V 10% 1206 X7R
• 141d7104ka0 C1 CAP,NP 0.1uF 100V 10% 1210 X7
• 128e106ma01 C16,17 CAP,E NP 10uF 100V 20%
• 141d7104kb0 CAP,NP 0.1uF 200V 10% 1210 X7
• 19016tl072dts IC1 SMD I.C. TL072CDT SGS Dual Op-Amp Semiconductors
• 19209124126qs Q1,4,5 TRANS, NPN 50V 0.15A 2SC2412K
• 19209139066rs Q2,8 TRANS, NPN 120V 0.05A 2SC3906K
• 19209210376qs Q7,9 TRANS, PNP 50V 0.15A 2SA1037K
• 19209215146rs Q3,6 TRANS, PNP 120V 0.05A 2SA1514K
• 19703rls4148s D1,2,3,4,5,6 Diode RLS4148
• 19915000563s Z1,2 ZENER 5.6V 5% PHILIPS BZX84-C5 V6
• 19915001203s Z5,6 ZENER 12V 5% PHILIPS BZX84-C12
• 19915001503s Z3,4 ZENER 15V 5% PHILIPS BZX84-C15
• 192232irf9640 Q10 FET IRF9640 IR P-CH TO220
• 192233irf640 Q11 FET IRF640 IR N-CH TO-220
• 1759f40hr2 Wafer 40PIN PITCH=2.54mm HR2* Miscellaneous
• 12214121m4191 L1 Ferrite core LS-A6206-ST EFD-30
• 12214350j4180 L2 Inductor 35uH
• 06-t3085020 PCB TO H/S-2,PCB TO PCB/H-4 SCREW 3*8
• 06-t31207 TO HSQLC1004/ID150-1 SCREW M3*12